with Lifting Ring / with Wire Loop, without Rest Position

GN 717 Stainless Steel Indexing Plungers, Guide Stainless Steel

Stainless Steel Indexing Plungers Guide Stainless Steel GN 717 thumbnail

Stainless Steel Indexing Plungers Guide Stainless Steel GN 717 sketch

Type

A	With pull ring, without locknut
AK	With pull ring, with locknut
D	With wire loop, without locknut
DK	With wire loop, with locknut

Show filter

d₁ Plunger -0,05 Bore +0,03/+0,08	d₂	d₃	d₄	e	l₁	l₂	l₃	l₄	l₅ min.	l₆	l₇	A/F	max. tightening torque in Nm	Spring load in N≈ initial	end

3	M 6	14	6	6,9	33,5	3,5	12	4,5	10	32,9	12,9	6	2	3	12
3	M 6 x 0,75	14	6	6,9	33,5	3,5	12	4,5	10	32,9	12,9	6	3	3	12
4	M 6	14	6	6,9	33,5	4	12	4,5	10	33,4	12,9	6	2	3	12
4	M 8 x 1	14	6	9,2	40,4	4,5	16	6	13,5	42	15,5	8	8	5	24
5	M 8	18	7,2	9,2	45	5	16	6	13,5	42,5	15,5	8	7	5	24
5	M 8 x 1	18	7,2	9,2	45	5	16	6	13,5	42,5	15,5	8	7	5	24
5	M 10 x 1	18	7,2	11,5	45	5	16	6	13,5	42,5	15,5	10	22	5	24
6	M 10	24	9,5	11,5	57,1	6	20	7,5	17	54,4	20,9	10	15	5	21
6	M 12 x 1,5	24	9,5	13,8	57,1	6	20	7,5	16,5	54,4	20,9	12	38	5	21
8	M 12	30	11,8	13,8	71	8	24	9	20,5	66,9	25,9	12	20	6	22
8	M 12 x 1,5	30	11,8	13,8	71	8	24	9	20,5	66,9	25,9	12	20	6	22
8	M 16 x 1,5	30	11,8	19,6	71	8	24	9	20,5	66,9	25,9	17	80	6	22
10	M 16 x 1,5	30	11,8	19,6	74,8	10	26	9	22,5	70,9	25,9	17	80	4	27

Filter combination produces no result.

Specification

Threaded body
Stainless steelNI
Zinc plated, blue passivated

Plunger pin
Stainless steel AISI 303

Pressure spring
Stainless steel AISI 301

Lifting ring / wire loop
Stainless steel AISI 301

Load Rating Information

Stainless Steel Characteristics

Metric ISO Thread DIN 13

Metric ISO fine thread DIN 13

RoHS

Information

Stainless steel indexing plungers GN 717 are characterized by small dimensions. These indexing plungers are universally applicable due to their prevention of misalignments and positioning errors of the mating indexing bores.

Type A with pulling ring can be activated by finger in inaccessible places. If the indexing plungers are to be installed in areas which are not accessible by hand, type D with a pulling loop can be used for actuation from a distance. For example, this is possible with a retaining cable GN 111.2.

During assembly, the max. tightening torques shown in the table should not be exceeded when securing the lock nut.